Autoquip GATES SWING User Manual

GATE & ENCLOSURE INSTALLATION MANUAL SWING GATES P.O. Box 1058 • 1058 West Industrial Avenue • Guthrie, OK 73044-1058 • 888-811-98

LABEL PLACEMENT 10 36405690 36402680 36405680 36405670 36403210 Figure 1 - Label Placement Figure 2 – 36405695

LABEL PLACEMENT 11 Additional 36405680 Decal installed on the Gate Post, Same side as the Push-Button Station Decal Plates shown in Figure 1

LABEL PLACEMENT Additional 36405680 Decal installed on the Gate Post, Same side as the Push-Button Station Decal Plates shown in Figure 1 sh

13 INSTALLATION INSTRUCTIONS ITEMS TO BE SUPPLIED BY THE INSTALLER • 3/8” x 3 ½” (minimum) Anchor Bolts (8 per gate) • 3/8” x 3 ½” (minimum)

INSTALLATION INSTRUCTIONS GATE INSTALLATION SINGLE SWING GATE INSTALLATION 1. Position the gate on the floor in front of the lift. Make sure

INSTALLATION INSTRUCTIONS 9. Install the interlocks according to the Interlock Installation instructions in the next section. 10. Verify that

INSTALLATION INSTRUCTIONS Post Foot Plate Figure 4 – Gate Installation Temporary Brace Figure 5 – Temporary Brace 16

INSTALLATION INSTRUCTIONS Figure 6 Gate Components 17

INSTALLATION INSTRUCTIONS BI-PART SWING GATE INSTALLATION Installation for a bi-part gate is the same as a single swing. The only difference is

INSTALLATION INSTRUCTIONS INTERLOCK INSTALLATION INSTRUCTIONS There are two kinds of interlocks that can be used on swing gates, depending on the

TABLE OF CONTENTS Introduction 3Inspection and Identification 4Pre-Installation Site Visit 5Responsibility of Owners/Users 6Safety Signal Word

INSTALLATION INSTRUCTIONS All solenoid interlocks must be fail-secure. This means that in the event of a power failure, the gate must remain lock

INSTALLATION INSTRUCTIONS Status Switch Set Screw Mounting Bracket Solenoid Interlock Figure 8 – Single Swing Solenoid Interlocks Status Swit

INSTALLATION INSTRUCTIONS WIRING INFORMATION FOR SOLENOID • The solenoid requires 24-volt DC power. Applications of other power sources will re

INSTALLATION INSTRUCTIONS G.A.L. INTERLOCK (TYPE SM) – Single Swing Gates The G.A.L. Type SM interlock is used on single swing gates only. Insta

INSTALLATION INSTRUCTIONS 8. Verify operation of the upper level gate. NOTE: The cam must rotate the actuator arm in the upward direction at t

INSTALLATION INSTRUCTIONS Figure 11 – GAL Interlock (Type SM) 25

INSTALLATION INSTRUCTIONS Gate Post Interlock Mounting Pad Strike Mounting Pad Actuator Arm Strike Interlock Figure 12 – GAL Interlock Attach

INSTALLATION INSTRUCTIONS G.A.L. INTERLOCK (TYPE SDM) – Bi-Part Swing Gates The G.A.L. Type SDM interlock is used on bi-part swing gates only.

INSTALLATION INSTRUCTIONS WARNING! Never run the unit with the gates or doors open! The gates must not open when the lift is in operation or whe

INSTALLATION INSTRUCTIONS Actuator Shaft GAL Interlock (Type SDM) Corner Linkage Long Arm Mid-Position Linkage Figure 13 – GAL Interlock (

INTRODUCTION Autoquip Corporation has designed and manufactured these gates and enclosures to conform to ANSI Standard B20.1b in order to provide

INSTALLATION INSTRUCTIONS GAL Interlock Strike Strike Mounting Pad Interlock Mounting Pad Figure 14 – Interlock and Strike 30

INSTALLATION INSTRUCTIONS Short Arm 3/8” Socket Head Shoulder Screw Actuator Shaft Set Screw Long Arm Figure 15 – Corner Linkage Wheel Actu

INSTALLATION INSTRUCTIONS Actuation Cam Actuator Arm Handrail or Stanchion Figure 17 – Lower Level Cam Actuation Actuation Cam Handrail or St

INSTALLATION INSTRUCTIONS ENCLOSURE PANELS Look at the plan views on the lift General Arrangement drawing to see the basic layout of the panels.

INSTALLATION INSTRUCTIONS Corner Angle Figure 19 – Corner Angle 34

INSTALLATION INSTRUCTIONS Top Cap Splice Figure 20 – Top Cap Splice 35

ROUTINE MAINTENANCE DANGER! To avoid personal injury or death, all maintenance procedures described in this section should only be performed

REPLACEMENT PARTS LIST Specific part numbers vary from job to job, depending on the model and options chosen for the application. Call the Autoqu

LIMITED WARRANTY The user is solely responsible for using this equipment in a safe manner and observing all of the safety guidelines provid

INSPECTION & IDENTIFICATION The following items are typically shipped loose within each manually operated Vertical Gate order: A. Gate wit

PRE-INSTALLATION SITE VISIT SITE CONDITIONS Whenever possible, make a pre-installation visit or call someone at the site. Installers must be fami

RESPONSIBILTY OF OWNERS/USERS CODE COMPLIANCE Ultimate responsibility for gaining state and local code approval is the responsibility of the buyer

SAFETY SIGNAL WORDS SAFETY ALERTS (Required Reading!) The following SAFETY ALERTS are intended to create awareness of owners, operators, and maint

SAFETY PRACTICES DANGER! High voltage! May cause personal injury or death. Repairs should only be performed by a qualified service/control tec

SAFETY PRACTICES WARNING! Support all posts and components! Illustrations in this manual may show them unsupported. This is done in order to make